Recently Steven was wearing a still-pretty-nice pair of jeans and somehow ripped an L-shaped hole in the knee.

So I decided to mend them as I was taught by my mom, who over the years raised three boys on a farm and mended countless torn jean-knees. I think she even patched patches at times.
After I had a little boy who wore out knees, I asked her to teach me how to patch pants.
There's something very satisfying about taking a comfortable, torn, pair of jeans and making them all neat and mended.
It's even more satisfying when you can say, "I am mending pants," in Pennsylvania German. "Ich bin am hossa flicka," or "Eeehhh* bin ahm hossa flicka."
*deep H sounds from the back of your throat
So: a tutorial, in case you would like to learn this skill as well. And a note: there are a number of ways to mend jeans. This is only one of them.
You will need:

1. a stash of denim pieces. Start collecting these long before you have anything to mend. If you throw out a worn pair of jeans, cut out a few sections from the back of the leg--usually the fabric is still good there. Or save the bottom part of the legs when you make cut-offs.
2. A good sharp sturdy needle
3. A thimble, if you like. Mom ALWAYS used a thimble for "flicking" but I've never learned how to do it "chite," i.e., as it ought to be done.
4. Thread. Surprisingly, gray thread is the most invisible on blue denim. I used beading thread because it's so thick and tough, but it's also very obvious. But that doesn't matter if you're going to wear the jeans for sacking seed, and also the stitches show up better on pictures for a tutorial.

5. Scissors and pins.
This is what you do:
1. Turn the pant leg inside out and lay it flat on a table or ironing board. As you can see, this was a pretty clean tear, but this method works for worn-through knees as well.

2. Find a piece of denim from your stash that's close in color and weight to the torn pants.

3. Cut this scrap piece of denim about 2 inches bigger all around than your hole. The exception to this is side seams--it's much easier if you don't have to maneuver around seams, so in that case, less than 2 inches is fine.
4. Serge around the edges of the patch.

5. Lay the patch right-side-down on the hole and pin all around the edge.



6. Prep your needle and thread. You don't want a long tangly piece of thread, so start with a piece maybe 30 inches long and knot the ends together so you're working with a double thread.
7. Put one hand inside the pant leg and with the other, take running stitches all around the outside edge of the patch, just inside the serging. 1/4 inch stitches are fine. You can also go with tiny stitches on the right side and longer stitches on the inside, if you want it to look a little more discreet.


Keep going, all the way around the edge of the patch.
Unpin as you go.
8. Turn the pant leg right-side-out. I didn't get a good picture of what it should look like at this point but you'll get the idea from the next shots.
9. Next you get to play surgeon. Your patient got gangrene and you get to cut away the dead flesh. So snip away--all the frayed areas and worn-thin spots and loose threads.

10. Now you want to turn under all those raw edges around the patch about 1/4 inch and pin them in place.

When you get to a curve or corner, cut a little snip so it'll turn under nice and neat.

11. Thread your needle again and take little "invisible" stitches all around, sewing the edges of the hole to the patch underneath. Again, keep one hand up the inside of the pant leg. And pull it out every so often to make sure things are still on course. It's very easy to shift and tuck but it's not the end of the world if this happens.



Finally you'll be all the way around. Take a few stitches on top of each other to secure the thread and snip it off. Make sure you pull all the pins or the wearer will never trust you again.
And you're done!

Here's me and my mom.
